Choosing a watch subcontractor: what to ask
A watch subcontractor can design the case of a watch, make its prototypes, assemble it, inspect it and handle its after-sales service. Depending on the workshop, some of these steps are done on site and others go to partners. Before placing an order, a brand therefore asks who does what and where, from what quantity, what happens to the drawings, which values final inspection checks, how long each step takes, and what the workshop can attest for Swiss made. The eight questions below apply to any subcontractor; we give our own answer to each.
The eight questions
Each question calls for a written answer, which then goes into the quotation or the specification.
| Subject | Question to ask | What the answer specifies |
|---|---|---|
| Scope | Who carries out each step, and where? | A step-by-step list: done in the workshop or sent to a partner, with the place |
| Batches | From what quantity do you take an order? | A minimum for each operation, and the quantity required for machining |
| Confidentiality | Which agreement protects my drawings, and what do you show of your clients’ work? | The non-disclosure agreement, the people it binds, the use of images |
| Drawings | Which files do I receive, and may I take them to another workshop? | The deliverables of each phase and the rights to the design and the drawings |
| Final inspection | What do you check on each watch, and to which values? | Test pressures, rate tolerance, what happens to a rejected piece, the report |
| Lead times | How long does each phase take, and counted from when? | A lead time for each phase, the event that starts it, what depends on third parties |
| Swiss made | What can you attest in writing? | The place of each operation and the Swiss share of the components delivered |
| After-sales service | Do you take watches back for service, and on what terms? | Diagnosis before any work, spare parts, checks before the watch goes back |
Scope: who does what, and where
A watch goes through ten steps: exterior design, case engineering, prototypes, industrialisation, machining, finishing, assembly, casing, final inspection, then after-sales service. A workshop that offers a project “from drawing to after-sales” does part of it on its own premises and sends the rest out. The brand asks for the list step by step, with the place where each step is carried out, who orders it when it goes to a partner and who checks the part when it comes back.
The place matters for the indication of origin. The watch ordinance places in Switzerland the mechanical construction and prototyping of a mechanical watch, its casing and its final inspection1. The Geneva Seal regulation places in the canton the assembly, adjustment and casing of the movement, together with the inspection of the watch head2. For Swiss made, the answer that counts is therefore the country; for the Geneva Seal, the canton.
The brand also asks what the subcontractor designs, because the watch exterior and the movement are two separate trades. We design the watch exterior: the case, bezel, dial, caseback, crown and any other component it needs. It is designed around the movement the brand chooses, from its casing dimensions.
| Step | What is done | Carried out by |
|---|---|---|
| Design and engineering of the watch exterior | Sketches, 3D renderings, dimensioned drawings and 3D files for machining | CLD offices, Plan-les-Ouates |
| Prototypes and industrialisation | First parts assembled, assembly and finishing trials, manufacturing routings, inspection plans, pre-series | CLD workshop, Plan-les-Ouates |
| Machining | Parts machined to the drawings, checked on arrival in our workshop | Partner workshops, Plan-les-Ouates |
| Finishing | Jewellery work on case components and polishing | CLD workshop, Plan-les-Ouates |
| Assembly and inspection | Case assembly, crystal bonding, movement assembly, casing, final inspection | CLD workshop, Plan-les-Ouates |
| After-sales service | Written diagnosis, repair, inspection and return; a component that has to be remade is machined by our partner workshops | CLD workshop, Plan-les-Ouates |
| Movement, dial, hands, crystal | Components from suppliers: we find these suppliers, or the brand delivers its own | Suppliers |
We order the machining and we are answerable for it. Each step can also be ordered on its own.
Our page on Swiss watch development in Geneva follows these steps phase by phase and says, for each one, what the brand receives.
Minimum batches and quantities
The minimum order depends on the operation. Case assembly, casing and inspection are bench work, done piece by piece. Machining has to be set up before the first part is cut, and that preparation weighs more heavily on the price of a small batch.
The brand asks for a minimum for each operation instead of one overall figure, then for the quantities planned at each phase: prototypes, pre-series, first production batch.
We have no minimum batch for the operations carried out in our workshop, which can be ordered from a single piece. An independent brand can have a few pieces assembled; inspection and batch documentation stay the same. For a project that includes machining, the quantity is set in the quotation.
Confidentiality
A drawing sent for a quotation is read by the engineering office, then by the machining workshop when that step goes to a partner. Before sending anything, the brand asks which non-disclosure agreement covers the exchange, and whether it also binds the partners who will receive the drawings.
It then looks at what the subcontractor shows of its other clients’ work. Recognisable watches on its website or social media indicate what it will do with the brand’s own. A workshop that names no one cannot give references: it is judged on a short first order, a single operation or a small batch.
At CLD Design, a non-disclosure agreement is signed on request before any technical exchange. We never name the brands we work for, on this site or in our sales communications, and we do not discuss ongoing work outside the company. In after-sales service, we appear neither on the documents given to the end customer nor in any exchange with them.
Drawings: what the brand receives and keeps
The design of a watch produces sketches and 3D renderings. Engineering produces the dimensioned drawings and the 3D files from which the parts are machined. Three questions come before the first sketch: which files the brand receives, at what point, and whether it may take them to another workshop.
The answer is written into the quotation. The rights to the design and to the drawings are set by a written agreement between the brand and its subcontractor, which an intellectual property adviser can review.
The brand has two reasons to keep dated drawings. The first concerns the indication of origin. Whoever uses an indication of source must prove that it is accurate3, and the FH guide states that prototyping in Switzerland is proved with documents such as drawings, invoices or accounts4. The second concerns after-sales service: a case component that is no longer in stock is remade from its dimensioned drawings, and the brand must be able to pass them on to the workshop that handles its returns.
In a project run by us, the brand receives sketches and then 3D renderings at the design stage. At the engineering stage it receives the dimensioned drawings and 3D files of the case, bezel, caseback and crown, ready for machining. The drawings of a watch we developed are already on file with us when it comes back for service.
Final inspection and water resistance values
What to ask: what is checked on each watch, with which equipment and to which value. A useful answer gives a pressure, a tolerance and a frequency: every piece, or a sample.
For water resistance, two standards serve as benchmarks. ISO 22810 requires a water-resistant watch to withstand, among other tests, a water overpressure of at least 2 bar for 10 min, and equates 1 bar with 10 m of water depth5. ISO 6425 covers divers’ watches, designed for at least 100 m, and requires a water resistance test on every watch produced6. For the Geneva Seal, every watch is checked at the value stated by the brand, with a minimum of 2 bar under pressure and 0.5 bar under vacuum2.
ISO 22810 describes the tests that apply in a dispute and leaves the watch manufacturer free to choose its production tests5. For a watch made with a subcontractor, that choice falls to the brand. It writes into its specification the stated value, the pressure of the production test, and whether that test covers every watch or a sample. It also writes in the rate tolerance, the functions to be checked, what happens to a rejected piece and the document that goes with each batch.
Our final inspection covers a visual inspection of the whole case, a functional test of the movement and an instrumented water resistance test, as standard at 0.5 bar under vacuum and 3.0 bar under pressure; higher values are available on request. Any non-conformity is isolated and recorded, and no part that has not passed inspection leaves the workshop. Each batch has its own file, opened on receipt, and the inspection report is supplied on request. These values are given on our page on watch subcontracting in Geneva, final inspection.
Lead times
A lead time is asked for phase by phase, with the event that starts it: approval of the design, arrival of the components, sign-off on a prototype.
Part of the lead time depends on third parties. The movement, dial, hands and crystal come from suppliers, and machining may go to a partner: their lead times are added to the workshop’s own. A precious metal case also goes through official control, which it must undergo before it is placed on the market7.
At CLD Design, assembly and inspection operations take one to two weeks for a simple watch once it is in our production flow; beyond that, the lead time is set in the quotation. For a development project, the schedule is set in the quotation, phase by phase, with an indicative lead time. It depends on the brand’s starting point, from an idea to technical drawings, and on the quantities.
Swiss made: what the subcontractor can attest
The watch ordinance sets five conditions, and they are cumulative1:
- for a mechanical watch, the mechanical construction and prototyping of the watch as a whole are carried out in Switzerland;
- the movement is Swiss;
- it is cased in Switzerland;
- final inspection is carried out in Switzerland by the manufacturer;
- at least 60% of the manufacturing costs are incurred in Switzerland.
Writing “Swiss made” is the brand’s decision. It is taken without prior authorisation, and the law leaves the proof to whoever uses the indication3. A subcontractor can attest two things: the place where it carried out its operations, and the Swiss source or the percentage of Swiss value of the components it delivers. The FH guide advises asking each subcontractor for that attestation in writing4. The right to the indication depends on the whole watch, including the movement and the 60% calculation. A workshop that makes only part of it therefore cannot guarantee it.
The case has criteria of its own. It is Swiss if it has undergone at least one essential manufacturing operation in Switzerland (stamping, machining or polishing), if it was assembled and inspected there, and if at least 60% of its manufacturing costs are incurred there1. The brand asks where the case is machined and where it is polished.
For our part, this is where the work is done. Engineering of the watch exterior is done in our Plan-les-Ouates offices, and prototypes are assembled and fine-tuned in our workshop. Machining is carried out by our partner workshops in Plan-les-Ouates. Polishing, assembly, casing and final inspection are done in our workshop. We issue no certification and we hold none. Swiss made also depends on the movement and on the manufacturing costs, so we cannot promise that a watch will qualify. The texts are set out article by article on our page Swiss made, Geneva provenance and the Geneva Seal.
After-sales service: who takes the watch back after the sale
Some of the watches sold come back to the workshop, during the warranty or after it. Under Swiss law, the seller is liable to the buyer for defects, and a warranty claim is time-barred two years after delivery8. The brand or its retailer keeps that commitment and hands over the technical work.
The question for the subcontractor that assembles the watches is whether it also handles returns, and on what terms: a written diagnosis before any work, where the spare parts come from, which checks are made before the watch goes back. ISO 22810 points out that water resistance depends on the watch’s history, servicing included5. A watch opened for service is tested for water resistance again before it leaves.
Two points concern drawings and gold. A service workshop that did not develop the watch needs the dimensioned drawings to remake a case component. On a gold case that is already hallmarked, replacing a part calls for a new test and a new hallmark; polishing that removes or damages the hallmarks also calls for a new hallmark9. The brand decides with the workshop who takes the case to the Assay Office.
We carry out after-sales service for brands, retailers and other watch subcontractors, including for watches developed elsewhere, which we reassemble to their original specifications. On arrival, each watch goes through a photographic inventory and a written diagnosis; no work starts until the client has approved it. It leaves after an instrumented water resistance test, a functional check and a final visual inspection, with its service report. The brand keeps the relationship with its customer, and the warranty. The article Outsourcing a watch brand’s after-sales service deals with spare parts, customs and turnaround times.
Frequently asked questions
Can the same subcontractor design the case, make the prototypes, assemble the watch and service it?
Yes. Some workshops run a project from the first drawing to after-sales service and send part of the work to partners. CLD Design SA, in Plan-les-Ouates (Geneva), designs and engineers the watch exterior, assembles and fine-tunes the prototypes, polishes, assembles, inspects and provides after-sales service in its own offices and workshop. Machining is carried out by its partner workshops in Plan-les-Ouates.
What minimum batch does a watch subcontractor ask for?
It depends on the operation, so ask for a minimum for each one. At CLD Design there is no minimum batch for the operations carried out in the workshop, which can be ordered from a single piece; for a project that includes machining, the quantity is set in the quotation.
Can a subcontractor guarantee that a watch will be Swiss made?
No. It can attest in writing where its operations were carried out and what share of Swiss value the components it delivers contain. The right to the indication depends on the five conditions of Article 1a of the watch ordinance (SR 232.119), including a Swiss movement and at least 60% of the manufacturing costs incurred in Switzerland. The declaration remains the brand’s, and the brand must be able to prove it (TmPA, Art. 51a).
Which water resistance values should final inspection check?
The ones the brand states for its watch. ISO 22810 requires a water overpressure of at least 2 bar held for 10 min and leaves the watch manufacturer free to choose its production tests; ISO 6425 requires a test on every divers’ watch produced. CLD Design’s standard water resistance test is run at 0.5 bar under vacuum and 3.0 bar under pressure, with higher values on request.
Who keeps the case drawings?
This is settled in writing before the design work starts: which files the brand receives, who holds the rights and whether the brand may have the drawings executed by another workshop. Dated drawings serve to prove that the construction and prototyping were done in Switzerland, and to remake a component during after-sales service.
Sources
- SR 232.119, Ordinance on the Use of “Switzerland” or “Swiss” for Watches, status as of 1 January 2019, Art. 1a (Swiss watch) and Art. 4 (case). English translation on Fedlex (no legal force) accessed 29 September 2026
- Geneva Seal regulation, Timelab, version 2.2 of 16 September 2026, applied since 18 September 2026, chapters 2 and 9 and appendix A.3. Regulation (PDF, in French) accessed 1 October 2026
- SR 232.11, Federal Act on the Protection of Trade Marks and Indications of Source (Trade Mark Protection Act, TmPA), status as of 1 July 2025, Art. 51a (burden of proof). English translation on Fedlex (no legal force) accessed 29 September 2026
- FH, Guide on the use of the designation “Swiss” for watches, version 5 of 13 September 2018, sections 1, 4.2.2, 4.2.3, 4.2.4, 4.8 and 4.9. The guide sets out the interpretation of the Federation of the Swiss Watch Industry and its authors accept no liability for its content; in case of dispute, only the French version is valid. Guide in PDF accessed 29 September 2026
- ISO 22810:2010, Horology, water-resistant watches, official public extract: foreword, introduction, clauses 1 to 4.3.5. Extract in English (PDF, iTeh Standards) · page on iso.org accessed 29 September 2026
- ISO 6425:2018, Horology, divers’ watches: scope and production testing (§ 4.1.6.2). Official extract in English (PDF, iTeh Standards) · page on iso.org accessed 29 September 2026
- SR 941.31, Federal Act on the Control of the Trade in Precious Metals and Precious Metal Articles (Precious Metals Control Act, PMCA), status as of 1 July 2023, Art. 13. English translation on Fedlex (no legal force) accessed 29 September 2026
- SR 220, Code of Obligations, Art. 197 and 210 (status as of 1 January 2026). English translation on Fedlex (no legal force) accessed 29 September 2026
- SR 941.311, Precious Metals Control Ordinance (PMCO), Art. 121 and 122 (status as of 1 January 2024). English translation on Fedlex (no legal force) accessed 29 September 2026
This article summarises official texts, standards and the industry guide, with their sources. It is not legal advice.